1314 Pc Programming Station Software Download

Posted on by
Station

Or, you can uninstall 1314-3302 PC Programming Station Dealer from your computer by using the Add/Remove Program feature in the Window's Control Panel. • On the Start menu (for Windows 8, right-click the screen's bottom-left corner), click Control Panel, and then, under Programs, do one of the following: • Windows Vista/7/8: Click Uninstall a Program. • Windows XP: Click Add or Remove Programs. • When you find the program 1314-3302 PC Programming Station (Dealer), click it, and then do one of the following: • Windows Vista/7/8: Click Uninstall. • Windows XP: Click the Remove or Change/Remove tab (to the right of the program).

• Follow the prompts. A progress bar shows you how long it will take to remove 1314-3302 PC Programming Station Dealer.

Member Registered: Posts: 96 Posted Edited it is a normal rs-232 serial interface. Just the 3 wires to connect, but some other wires have to be shorted at the PC end. The wires to short are the handshaking ones 4,6,1 shorted together 7,8 shorted // Here is a 2007 version of the Curtis programmer software. If anyone has a newer version please add // I couldn't upload an EXE file here so changed the file extension to.rtf // Change it back to.EXE once downloaded ** EDIT, newer Version 4 of software nearer end of thread.

Jan 03, 2010  Free 1314 pc programming station download software at UpdateStar. Curtis Model 1314 PC Software download. Power wheelchair board for REAL info! Be sure you get the 4401 version of the program as it provides engineering level access.

Hello; I have been reading the forum up and down looking for any clue about my connection problem. As I didn't find anything I am opening this thread (well, I found lots of hints about connection problems and tried many of them, but it seems my problem is somewhat different). I got a Curtis 1236, used. I don't know much about it's previous settings or use conditions. I tried connecting to it without motor, throttle.Terminal software (putty & dacio) showed error codes (scode x) signaling the parts that were missing, like the motor.

Curtis software 1314, however, refused connection: 'Error 0023 Initialization of communication interface failed. Communication error with controller' After assembling all the parts requested by the controller, the controller stopped printing error codes and printed run info like RPM, Amps, etc.I can change that info with the 'menu mode' switch. Again, I can see all that using putty, dacio, etc. The controller seems to work, it will accelerate the motor (the encoder settings are probably wrong, but it works anyway).

But the programmer software still refuses to connect. I have tried 4 differente USB/Serial adapters, some will show the terminal output correctly, others will not. I even tried with an old win98 PC, but the programming software still refuses to connect (terminal work though). Using an oscilloscope I have checked some bits are sent in the TX wire, but still conection is not established. I did also read about entering commands in the terminal, using ':'. Wirecast 7 download 32.

But it does not seem to work; sometimes the output of 'RPM x' info will stop for a moment but will resume activity soon. Some questions for the experts: - I have a 840 display installed, it shares the bus with the programmer cable. Is that ok with the programming process, or should I remove it? (I tried with & without). - Can be the Curtis controller set up as non-programmable? Is it possible or controller is programmed (using VCL) to avoid programming?

Free Pc Programming Software

- I have seen captures of users sending commands in the terminal. My terminals are full of controller output text (RPM - RPM - RPM.). Maybe there is a 'program mode' or something similar I have overlooked? Hope somebody can offer a clue. Hello; I have been reading the forum up and down looking for any clue about my connection problem.

Curtis 1314 Pc Programming Software

As I didn't find anything I am opening this thread (well, I found lots of hints about connection problems and tried many of them, but it seems my problem is somewhat different). I got a Curtis 1236, used. I don't know much about it's previous settings or use conditions. I tried connecting to it without motor, throttle.Terminal software (putty & dacio) showed error codes (scode x) signaling the parts that were missing, like the motor. Curtis software 1314, however, refused connection: 'Error 0023 Initialization of communication interface failed. Communication error with controller' After assembling all the parts requested by the controller, the controller stopped printing error codes and printed run info like RPM, Amps, etc.I can change that info with the 'menu mode' switch. Again, I can see all that using putty, dacio, etc.

Based on my test, here’s what I consider the top three mtv video downloader. Above all, using this tool, you can download 100% videos from any sites you watch online. Download mtv videos mac. Top three mtv video downloader Video Download Capture Video Download Capture is designed for downloading and converting videos from websites. It deserves to be at top for it is fast, easy to use and with a user-friendly interface.